翅片位置对复合式减涡器减阻性能影响数值模拟

为了探索翅片-管复合式减涡器的翅片安装位置对共转盘腔径向内流压力损失的影响规律,对不同转速、翅片周向位置及安装角度下的去旋系统开展了数值研究,得到了不同工况下共转盘腔径向内流的流场结构及压力损失分布曲线。研究结果表明:减涡管能引导流体径向流入,并降低流体的旋流比;相比于管式减涡器,翅片-管复合式减涡器能明显降低盘腔内的总压损失;在不同旋转雷诺数下,翅片的周向安装位置α及安装角β均存在最佳值;在中、高旋转雷诺数下,最佳值分别为α=9°,β=30°,最佳结构下总压损失较基础模型低40%左右;改变翅片周向位置及安装角度可以明显改变气流进入减涡管的角度,在较优情况下,可以减小流体流入减涡管的阻力及在减涡管内的流动阻力,整体上减小了盘腔内总压损失。     

接受孔形状对预旋供气系统内气流流动影响研究

为对比不同形状接受孔的预旋系统内气流流动特性,通过数值模拟方法,对带有不同形状接受孔的预旋系统进行了研究。研究发现:收缩型接受孔入口截面气流流通面积较大,相对速度较小,在预旋系统中的性能最优,其次是类梯型,最后是直孔型。同一旋转雷诺数下,带收缩型接受孔的预旋系统无量纲温降较直孔型提高5.8%,总压损失系数降低3.0%。三种类型接受孔的预旋系统无量纲温降和总压损失系数均随进出口压比的增加而增大,在相同压比下,收缩型接受孔预旋系统无量纲温降最大,总压损失系数最小。     

基于响应曲面法的高速内冷铣削AISI304不锈钢铣削力

针对硬质合金刀具高速内冷铣削AISI304不锈钢时,切削力大、切削温度高及加工表面质量低的问题。基于响应曲面中心复合设计方法进行高速内冷铣削实验,建立了铣削力分量二阶回归预测模型,并进行了实验验证。对比了干式与内冷铣削后的加工表面质量,分析了铣削参数对铣削力分量的影响规律,以铣削力分量最小为目标优化了铣削参数。结果表明:进给力和径向力的预测值与实验值的误差分别为4. 77%和6. 16%;内冷铣削的Ra为0. 193～0. 327μm;对铣削力分量的影响是铣削深度转速进给量,随着铣削深度和转速的增加,进给力先升高后降低,径向力逐步增加,铣削深度与转速的交互作用对进给力和径向力的影响显著;转速11 643. 63 r/min、铣削深度1 mm、进给量0. 08 mm/r为最优铣削参数组合。     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

考虑重力的风机叶片水平加载测试方法

在风电叶片三维有限元参数模型中引入了重力产生的附加载荷,仿真计算了风电叶片水平加载方式的静载荷测试中附加载荷产生的水平方向的耦合位移,分析了耦合位移对测试过程中理论计算结果的影响;由于重力的叠加效应,测试中某些截面实际施加的等效载荷可能远超叶片设计的目标测试载荷,建议联合有限元分析,优化叶片安装角度和加载力方向的方法,降低叶片局部截面实际施加等效载荷的过载峰值。     

超声速串列静叶积叠优化分析

在进口超声速、气流转折角大的高负荷条件下,静叶通道中激波强度高,激波、附面层干扰引起的损失大,且静叶中三维流动引起的径向载荷分布不均匀,易产生角区分离。叶片积叠优化是提高风扇性能的一项有效技术。采用数值模拟的方式研究了不同积叠形式对优化串列静叶沿展向激波结构,改善叶排间流动匹配的作用。三维流动对比分析可以得出:高负荷串列静叶采用正弓形积叠,叶片展向载荷分布合理,静叶端壁角区分离损失减小,前后叶片排流动匹配较好,风扇性能进一步提高。     

一种浮空器压力调节综合控制系统设计

针对现有浮空器压力控制系统设计的不足,结合浮空器的使用环境,提出了一种基于双机冗余热备份、嵌入式CPU、高精度实时数据采集与处理的压力调节控制装置解决方案。首先建立了浮空器的压差数学模型;接着,以该模型为基础,进行压力调节控制系统设计,包括多余度压力控制系统设计、仲裁融合应急处理设计、压力自控设计。最后,采用该种设计的系留气球的空中试验结果表明,该压力系统控制能够根据气球所处不同的工作状态,融合传感网络状态信息,自主选择自控程序入口,较好的对气球气囊压力进行了有效调节与控制,保证了气球的安全。     

基于DDES的有／无舱门腔体气动噪声仿真分析

采用延迟分离涡仿真（ DDES）的方法研究了空腔和带有舱门的腔体的气动噪声特性。仿真在自由来流M＝0．85下,长宽深比值为5：1：1的矩形开放腔体展开。空腔仿真的声压级幅值结果与试验数据相比误差在4％以内,频率位置的预测较好。 DDES方法对于气动噪声问题具有很好的仿真准确性。空腔仿真结果和带有舱门的结果对比后表明,舱门迫使剪切层气流更多的撞击后壁进入腔体内部,使腔体内部尤其是中部压强波动增大,声压级在低频部分增量显著,达到了5 dB左右。     

某3级风扇试验流场诊断及性能优化

压气机试验是检验压气机设计是否达标的重要过程,并可在原设计基础上进行优化来发掘设计的潜能。利用级间总压和壁面静压在某3级风扇第1阶段试验对级间流场进行了详细测量和级性能诊断,提出了静叶角度优化方案;通过第2阶段试验,得出了角度优化后使设计转速喘振裕度提高了7.5个百分点,达到了设计指标的结论。流场诊断技术在压气机试验中起到了关键作用。结果表明:壁面静压结合级间径向总压测量方法基本能够满足在压气机试验中性能优化的需要。